4 Ch Reversible 8 kV/3 mA (8 W) NIM HV Power Supply Module (USB)
N1470
The CAEN Mod. N1470 provides 4 independent High Voltage channels in a single width NIM mechanics. Two and one channel versions (N1470A and N1470B) are also available. Each channel can provide a ±8kV max voltage, a 3 mA max current and a 9 W max power (8 W max power when output voltage is larger than ±3 kV). The output polarity is independently selectable for each channel.
|
SHV connector NIM single width, 4 channels for Mod. N1470, N1470B (1 Ch), N1470A, N1470AL, N1470AR (2 Ch) |
Consult our connectors reference page for technical information.
Channels have common floating return (common return insulated from the crate ground); HV outputs are delivered through SHV connectors.
The HV output Ramp-up and Ramp-down rates may be selected independently for each channel in the range 1÷500 V/s in 1 V/s steps. The module features 50nA Iset/Imon resolution. Features include Imon Zoom, increasing resolution to 5 nA.
Power supply control can be performed either locally, assisted by a Graphic color display or remotely, via USB, RS232 or RS485, the latter allowing to build a daisy chain network of modules N14XX. It is also controllable via TCP/IP by the Smart Fan Unit of CAEN NIM8301.
A complete set of free software Tools is available to control this unit: GECO2020 with user friendly GUI and CAEN HV Wrapper library for custom SW development. EPICS and LabVIEW also supported.
Safety features allows the module to perform as a current generator and includes:
|
Overvoltage and Undervoltage warning |
when the output voltage differs from the programmed value by more than 2% of set value (minimum 10V). |
|
Overcurrent detection |
when a channel attempts to exceed the programmed current limit, it signalled to be in “overcurrent” and enter in a TRIP status. The output voltage is varied to keep the current below the programmed limit for a programmable TRIP time, then the channel is switched off. If TRIP is set to “constant current mode”, the channel behaves like a current generator. |
|
VMAX |
programmable VMAX protection limit. |
|
Safety Board Interlock |
Common Interlock logic for channels enable/disable and individual inputs signal for channel Kill function. |
Module control can take place either locally, assisted by a Graphic colour display, or remotely, via USB (1) or RS485 (1). It is also controllable via TCP/IP (2) by the Smart Fan Unit of CAEN NIM8301 crate:
Special versions available:
-
2 channels version (N1470A)
-
1 channel version (N1470B)
-
2 channels Low Cost version only locally controllable (N1470AL)
-
2 channels Low Cost version only remotely controllable (N1470AR)
-
4 channels, 2U NIM module with 220/110 Vac plug for desktop operation equipped with 2.8″ Touchscreen, Ethernet and USB interface (NDT1470)
-
4 channels, 2U NIM module equipped with 2.8″ Touchscreen, Ethernet and USB interface (N1470ET)
Available Options:
-
A1480 DC Input Power Equalizer.
N14xx modules are provided with a USB VCP interface and can be programmed via PC by connecting the PC USB port with the N14xx USB B-type port; the featured controller (FT232BM chip) requires a driver available on this page or at www.ftdichip.com
Features
-
4 independent channels in 1U NIM module (2 & 1 channel versions also available)
-
8 kV / 3mA output range
-
Max output power:
-
9 W (<3 kV output)
-
8 W (>3 kV output)
-
-
Channels with individually selectable positive or negative polarity
-
SHV output connectors
-
Common floating return
-
Low Ripple
-
Under/over-voltage alert, overcurrent and max. voltage protection
-
Interlock logic for board enable and Individual channel kill
-
5 nA Current monitor resolution (with x10 Imon-Zoom: 500 pA)
-
Graphic color display
-
Local and Remote control (USB2.0/RS485/RS232)
-
Daisy-chain capability
-
Optional DC Input Power Equalizer
-
Software Tools for easy channel management
N1470: Manuals
Request a Quote
Footer
